Category 6 LAN cables in bulk are reliable LAN cables to provide the best data transmission speed. The inner conductors are not signal amplifiers or boost the ethernet cable speed. However, the strength of the cable depends on the conductor’s diameter (Capacity to transfer bulk information), speed either gigabit or 10 Gbps, and bandwidth (Throughput).
The distance plays an important role in the signal transmission and if the length of the cable is above 328ft you will feel slow speed. So, measuring the length and install according to the recommended length is preferable.
This guide will summarize the debate on boosting the ethernet cable strength of Cat6 cable. This blog will explain the need for ethernet cable strength. Each category cable has its power and capacity to work so do not generalize the category cables.
Let’s understand this guide with the help of Cat6 ethernet cable, the modern bulk ethernet cable in the networking industry.
Factors Contribute To Cable Strength
LAN cables are twisted pair cables and therefore they are more durable to install to reduce signal bleeding. Yeah, the cable signal does bleed if they are exposed to high interference beyond their capacity.
The major impact an ethernet cable has is the design to get maximum protection from the external environment and other factors that are not ignorable. So what is the Cat6 plenum 1000ft bulk cable boosting strength?
- Cable Category — A bulk cat6 plenum cable is the most secure combination for installation. The plenum HVAC cable is just perfect for the air handling spaces and ultimately for the best data transfer.
- Cable Quality — To judge the quality of bulk cat6 plenum copper cable you can peek inside the cable. You will witness tight twisted pairs, spline, and cable assembly in a seamless and undamaged design.
- Environmental Factors — The plenum HVAC jacket has no major impact on the environment due to its fire resistance and LSZH material capacity. On the other hand, copper is a recyclable material and can be reused.
- Speed — Fast Ethernet (100 Mbps) is better for the SMEs but large enterprises need at least 1000 Mbps (Gigabit) or 10 G (10 Gigabit).
- Termination — It will give your cable to work perfectly when you obey the right wiring standards. Cat6 can be operated with both T568A and T568B wiring standards.
These are the factors that will enhance your cable performance. The main thing is to get the right speed. Other things add a boost to the ethernet cable performance. What it could be — Cat6 Shielded plenum cable (F/UTP) variant used in complex building structures.
How Shielded Cables Are Secure?
UTP (Unshielded Twisted Pair) cables are the general form of network cables without any additional insulation layer. But In Cat 6 shielded plenum cables there is an additional layer that is either made of Aluminum Foil or Braided Mess.
These provide extra protection and act as a shell for the EMI or RFI to enter the signal stream. Furthermore, shielded cables are the same as the UTP Cat6 Plenum 1000ft cables with an additional insulation layer.
The insulation layer of the Aluminum Foil (F) or Braided Mess (S) is beneath the cable jacket. There is a transparent PE (Polyethylene) tape to protect the cable and a drain wire for grounding while installing the cable.
Shielded cables are used where UTP cables fail to work properly. They are quite expensive and there are different variants that you need to understand according to the nature of your environment.
- F/UTP — Foil/Unshielded Twisted Pair means the whole length of the cable is foil shielded but the twisted pairs are unshielded.
- S/UTP — The whole length of the cable is braided while the twisted pairs are unshielded.
- S/FTP — The whole length of the cable is covered with a braid mess and the twisted pairs are foil shielded.
- U/FTP — there is no shield present throughout the cable’s length but the twisted pairs are wrapped with Aluminum Foil.
- SF/FTP — A hard and strong form of shielded cables, the entire cable length has braid and foil wrapped while the twisted pairs are foil wrapped.
- F/FTP — It uses a single type of shielding (Aluminum Foil) throughout the cable length and the twisted pairs.
What Are The Factors To Boost Ethernet Cable Strength
While keeping the transmission constant, the main thing is to check the server speed and the bulk ethernet cable specs. The Cat6 plenum is a fast cat cable that ultimately matches the two-speed specifications of 1000 Mbps (1 GB/s) and 10 GB/s.
Some factors make the Cat6 plenum a true cable for high-speed networking and its top-notch bandwidth. Here are some of the main factors
- Pure Copper Conductor
- Tight twisted pairs
- Improved crosstalk
- Shielding variants
- Spline between twisted pairs
- Outer jacket specifications
- Installation location
- Length of the cable
- Quality of the cable
Final Thought
When you are going to install the cable in your home or office the main thing is to look for the right type of cable that you call a true cable for supporting the high speed and bandwidth.
Just like the cat6 plenum cable, the best combination for infinity cable results. It is said to be the toughest cable for fire resistance and other things like crosstalk and signal attenuation. If you want to go with the shielded cable (Cat6 Plenum Shielded) all you need to do is to spend some more $$$$$ (Bucks) and you will end up with the fast cat cable for your daily needs.
Boosting ethernet cable speed is the major factor for those who demand speed and smooth networking. It will cater best to your networking needs and also support the two main speeds Gigabit Ethernet and 10 Gigabit Ethernet.
